MOTIVO ENDURO 2090

Product may differ from the image.

MOTIVO ENDURO 2090

Technical data sheet

Water-borne 1C clear coating for wood.
Very good filling power, very good scratch resistance as well as good grain accentuation.

The product can be used on all wood species and as a top coating for colour coated surfaces.
The coating contains light protection agents that effectively delay yellowing of the wood.

Description

Description
Product Description		Water-borne 1C clear coating for wood. Very good filling power, very good scratch resistance as well as good grain accentuation. The product can be used on all wood species and as a top coating for colour coated surfaces. The coating contains light protection agents that effectively delay yellowing of the wood.
Raw Material Base / Binder Type / Active Agent		Polyurethane / acrylic resin combination
Application		Interiors, furniture, kitchens or surfaces which are exposed to high chemical stress.
Certificates / Label		The lacquer film meets the requirement of: DIN standard 68861, 1B (chemical resistance)
Minergie Eco		compatible
Gloss Level		15,30

Technical Data

Technical Data	Product
Technical Data
Material Safety Data Sheet	259000
Density (20ºC)	1.007	g/cm³
Solids Content	33	± 1 w/w-%
Organic Solvent Content	5	± 1 w/w-%
VOC Content (EU)	70	g/L
Shelf Life at 20°C in Unopened Original Containers	max. 15 Months
Theoretical Coverage	120 g/m² → 8 m²/kg
The data apply for 25902000. Values can vary depending on color or gloss level.

Safety Data

Safety Data
Refer to the following safety data sheets as well as the instructions on the label
Product	259000 - MOTIVO ENDURO 2090-15

Application advice

Product		Data Sheet	Applied Quantity / Layer Thickness
Application advice Wood substrate
Stain:	Stain if required
Primer:	MOTIVO ENDURO 2090	2590	120 g/m²
Intermediate sanding:	With grain 220-280
Recoating:	MOTIVO ENDURO 2090	2590	120 g/m²

For further applilcation proposals please ask our representative.

Preparation

Preparation
	Substrate	Every substrate must be well-cleaned, dry and free from grease and oil.
	Untreated wood substrate	Always apply the product to freshly sanded surfaces. Wood sanding grain 180-220

Processing

Processing
	Preventative Measures	We recommend wearing personal protective clothing, even in cases where no local regulations are in force.
	Stir	Stir product well before use.
	Dilution	With water if necessary.
	Brush	Yes, in some cases, only small parts and strips
	Roller	No
	Trowel	No

Application

Application
		Viscosity	Dilution	Nozzle	Pressure	Spray Cycles
	Gravity Feed Gun	55" DIN 4 mm	5-20 %	1.8-2.0 mm	2-3 bar	2
	Suction Cup Gun	55" DIN 4 mm	0-5 %	1.8-2 mm	2-3 bar	2
	Airless-(Airmix) Spray Application	55" DIN 4 mm	0-5 %	0.23-0.28 mm	60-80 bar (material pressure). Atomising air pressure 1.0-1.5 bar	2
	HVLP Spray Gun	55" DIN 4 mm	0-5 %	1.8-2.0 mm	2-3 bar	2

Drying Time

Drying Time
	Drying Time	At 23°C and 65% rel. humidity
		Dust dry after:	60	minutes
		Touch dry after:	45	minutes
		Sandable after:	2.5	hours
		Recoatable after:	2.5	hours
		Fully dry after:	10	days
	Remarks	Resistant to chemicals after 14 days

Important Remarks

Important Remarks
Specific Restrictions	Depending on the type of wood, we recommend spot testing.
Storage Conditions	Store product tightly closed between +5 and +30° C.
Coating Removal	Strip
Equipment Cleaning	Immediately after use with water, dried up material with REINIGUNGSMITTEL S 8200-98

Haftung

This data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guarantees for use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees. Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to recognized engineering rules are the responsibility of the manufacturer, even if our employee was on site during handling. Modifications due to technical developments may be made. The latest version of this information is applicable. In special cases, please request separate technical specifications.

cross_products

REINIGUNGSMITTEL S 8200-98