MOTIVO KLARLACK 2080

Product may differ from the image.

MOTIVO KLARLACK 2080

Technical data sheet

Clear, water-borne, quick-drying 1C top coat. Can be used as base and top coat with good grain accentuation. Non-blocking and elastic.

Description

Description
Product Description		Clear, water-borne, quick-drying 1C top coat. Can be used as base and top coat with good grain accentuation. Non-blocking and elastic.
Raw Material Base / Binder Type / Active Agent		Polyurethane combination
Application		For furniture, interiors and general carpentry work.
Certificates / Label		Test standard compliance for: DIN 4102-1 B1 (low flammability)
Minergie Eco		compatible
Gloss Level		05,15,30,50

Technical Data

Technical Data	Product
Technical Data
Material Safety Data Sheet	258000
Density (20ºC)	1.029	g/cm³
Solids Content	36	± 1 w/w-%
Organic Solvent Content	2	± 1 w/w-%
VOC Content (EU)	65	g/L
Shelf Life at 20°C in Unopened Original Containers	max. 15 Months
Theoretical Coverage	100-120 g/m² → -8-10 m²/kg
The data apply for: 25853000. Values can vary depending on color or gloss level.

Safety Data

Safety Data
Refer to the following safety data sheets as well as the instructions on the label
Product	258000 - MOTIVO KLARLACK 2080-05

Application advice

Product		Data Sheet	Applied Quantity / Layer Thickness
Application advice Wood substrate
Stain:	Stain if required
Primer:	MOTIVO KLARLACK 2080	2580	110 g/m²
Intermediate sanding:	With grain 220-280
Recoating:	MOTIVO KLARLACK 2080	2580	110 g/m²

For further applilcation proposals please ask our representative.

Preparation

Preparation
	Substrate	Every substrate must be well-cleaned, dry and free from grease and oil.
	Untreated wood substrate	Always apply the product to freshly sanded surfaces. Wood sanding grain 180-220

Processing

Processing
	Preventative Measures	We recommend wearing personal protective clothing, even in cases where no local regulations are in force.
	Stir	Stir product well before use.
	Dilution	With water if necessary.
	Brush	Yes, in some cases, only small parts and strips
	Roller	In some cases, only small parts and strips With the addition of 0.5-1.0% MOTIVO ENTSCHÄUMER 3952-00.
	Trowel	No

Application

Application
		Viscosity	Dilution	Nozzle	Pressure	Spray Cycles
	Gravity Feed Gun	30-34" DIN 4 mm	0-5 %	1.8-2.0 mm	2-3 bar	2
	Suction Cup Gun	30-34" DIN 4 mm	0-5 %	1.8-2 mm	2-3 bar	2
	Airless-(Airmix) Spray Application	30-34" DIN 4 mm	0-5 %	0.15-0.23 mm	60-80 bar (material pressure). Atomising air pressure 1.0-1.5 bar	2
	HVLP Spray Gun	30-34" DIN 4 mm	0-5 %	1.8-2.0 mm	2-3 bar	2

Drying Time

Drying Time
	Drying Time	At 23°C and 65% rel. humidity
		Dust dry after:	60	minutes
		Touch dry after:	45	minutes
		Sandable after:	2	hours
		Recoatable after:	2	hours
		Fully dry after:	10	days

Important Remarks

Important Remarks
Specific Restrictions	For stairs, please use MOTIVO TE 2085. Warning: If the substrate or room temperature is high, carefully add 2-5% VERZÖGERER 0102-00 FOR WATER-BORNE VARNISH as necessary.
Storage Conditions	Store product tightly closed between +5 and +30° C.
Coating Removal	Strip
Equipment Cleaning	Immediately after use with water, dried up material with REINIGUNGSMITTEL S 8200-98

Haftung

This data sheet is for your reference and information only. The above data are correct to the best of our knowledge. We offer no guarantees for use and exclude any liability. This applies in particular to consequential damage. We are not liable for any advice given by our employees. Our employees give non-binding information only. Site supervision, compliance with handling regulations, and adherence to recognized engineering rules are the responsibility of the manufacturer, even if our employee was on site during handling. Modifications due to technical developments may be made. The latest version of this information is applicable. In special cases, please request separate technical specifications.

cross_products

REINIGUNGSMITTEL S 8200-98